Home > The Posts > Product Guides > 74HC373D Octal D-Type Transparent Latch IC – 8-Bit, 3-State Output
74HC373D - Toshiba Semiconductor and Storage

74HC373D Octal D-Type Transparent Latch IC – 8-Bit, 3-State Output

PRODUCT TECHNICAL GUIDE 74HC373D – Octal D-Type Transparent LatchThe 74HC373D is an 8-bit high-speed CMOS transparent latch with three-state outputs. It is designed for digital data storage, bus inter…

In Stock 6,260 Available Inventory
Part No.:
74HC373D
Manufacturer:
Toshiba Semiconductor and Storage
Package:
20-SOIC (0.295", 7.50mm Width)
Datasheet:
74HC373D.pdf
Description:
IC D-TYPE TRANSP SGL 8:8 20SOIC
Quantity:
Original Supply

Strict supplier screening and quality control support.

Datasheet Support

Help engineers quickly verify product specifications.

BOM Sourcing

Support multi-part procurement and RFQ matching.

74HC373D Octal D-Type Transparent Latch IC – 8-Bit, 3-State Output

PRODUCT TECHNICAL GUIDE

74HC373D – Octal D-Type Transparent Latch

The 74HC373D is an 8-bit high-speed CMOS transparent latch with three-state outputs. It is designed for digital data storage, bus interfacing and logic control applications requiring reliable data latching and output isolation.

8-Bit Latch 2V–6V Supply SOIC-20

01. Product Introduction

The 74HC373D is an octal D-type transparent latch with three-state outputs, belonging to the 74HC high-speed CMOS logic family. It integrates eight independent data latch channels into one integrated circuit, allowing multiple digital signals to be temporarily stored and transferred.

The device uses two main control signals: Latch Enable (LE) and Output Enable (OE). When LE is high, the outputs follow the corresponding data inputs. When LE becomes low, the previously applied data is retained. The OE input controls the output state, allowing all eight outputs to enter a high-impedance condition when disabled.

With a wide operating voltage range of 2V to 6V, low power consumption and high-speed switching characteristics, the 74HC373D is suitable for digital systems requiring data buffering, temporary storage and bus control.

02. Key Benefits

  • Eight Independent Latch Channels: Stores eight bits of digital data within a single IC.
  • Three-State Outputs: Supports high-impedance output operation for shared data bus applications.
  • High-Speed Operation: Provides fast propagation characteristics for digital logic systems.
  • Low Power Consumption: CMOS technology helps reduce static power consumption.
  • Wide Supply Voltage: Operates across a 2V to 6V supply range.
  • Simple Control Interface: Uses LE and OE signals for straightforward data storage and output management.
  • Compact Integration: Combines eight latch circuits in one 20-pin package.

03. Features

  • Octal D-type transparent latch
  • Eight-bit data storage capability
  • Three-state output configuration
  • Independent latch enable control
  • Output enable control
  • High-speed CMOS technology
  • 2V to 6V operating supply voltage
  • Typical propagation delay of approximately 12ns under specified test conditions
  • Low static power consumption
  • Balanced propagation delays
  • Input protection against electrostatic discharge and transient overvoltage
  • Suitable for digital bus interfacing and logic control

04. Package

The 74HC373D is commonly available in a 20-pin Small Outline Integrated Circuit (SOIC-20 or SO20) package, depending on the manufacturer and ordering suffix.

The surface-mount package supports automated PCB assembly and provides a practical solution for compact digital electronic designs.

  • Package Type: SOIC-20 / SO20
  • Number of Pins: 20
  • Mounting Type: Surface Mount
  • Package Body Width: Approximately 7.5mm
  • Logic Family: 74HC High-Speed CMOS
  • Device Configuration: Octal Latch

Package dimensions and ordering configurations should be confirmed against the selected manufacturer's datasheet.

05. Pinout

The standard 74HC373 20-pin configuration includes eight data inputs, eight three-state outputs, two control pins and two power connections.

Pin Signal Function
1 OE Active-low output enable
2 Q0 Data output 0
3 D0 Data input 0
4 D1 Data input 1
5 Q1 Data output 1
6 Q2 Data output 2
7 D2 Data input 2
8 D3 Data input 3
9 Q3 Data output 3
10 GND Ground connection
11 LE Latch enable
12 Q4 Data output 4
13 D4 Data input 4
14 D5 Data input 5
15 Q5 Data output 5
16 Q6 Data output 6
17 D6 Data input 6
18 D7 Data input 7
19 Q7 Data output 7
20 VCC Positive supply voltage

Operating principle: When LE is high, data inputs are transferred to the corresponding outputs. When LE is low, data is stored. OE is active-low: a low level enables the outputs, while a high level places them in the high-impedance state.

06. Specifications

Parameter Specification
Part Number 74HC373D
Product Type Octal D-Type Transparent Latch
Logic Family 74HC
Number of Bits 8
Output Type Three-State
Supply Voltage 2V – 6V
Propagation Delay Approximately 12ns (typical, specified conditions)
Control Inputs LE and OE
Data Inputs 8
Data Outputs 8
Technology High-Speed CMOS
Output Configuration Tri-State
Operating Temperature -40°C to +125°C (manufacturer dependent)
Package SOIC-20 / SO20
Mounting Type Surface Mount

Electrical characteristics vary slightly among manufacturers. Refer to the corresponding datasheet for guaranteed timing, output current, power consumption and absolute maximum ratings.

07. Equivalent and Alternative Components

When selecting an alternative to the 74HC373D, engineers should compare logic functionality, supply voltage, propagation delay, output drive capability, package and pin compatibility.

  • SN74HC373DWR: Texas Instruments octal D-type transparent latch with three-state outputs, available in a 20-pin surface-mount package.
  • CD74HC373M: Texas Instruments 8-bit high-speed CMOS transparent latch alternative.
  • MM74HC373WM: onsemi octal D-type latch with three-state outputs.
  • 74HCT373: Related HCT logic-family device with TTL-compatible input thresholds and three-state outputs.
  • 74HC573: Related octal transparent latch with three-state outputs and a different pin arrangement.

Replacement considerations: The 74HCT373 has different input threshold characteristics from the 74HC373. The 74HC573 is functionally similar but does not necessarily share the same pinout. Always verify electrical characteristics, timing requirements, package dimensions and pin assignments before substitution.

08. Manufacturer

The 74HC373D is a standard logic device produced by multiple semiconductor manufacturers, including Toshiba, Nexperia and other suppliers of 74HC CMOS logic products.

These manufacturers provide octal latch solutions designed for digital signal storage, bus control and data interface applications.

The 74HC logic family is widely used in electronic systems because of its low power consumption, broad operating voltage range and compatibility with many digital circuit architectures.

Manufacturer references:

Confirm the actual manufacturer and ordering suffix when purchasing, as the generic 74HC373D designation is shared across manufacturers.

09. Applications

The 74HC373D is suitable for digital electronic systems that require temporary data storage, signal isolation and parallel data management.

  • Microprocessor Systems: Provides temporary data storage and address/data bus interfacing.
  • Embedded Control Systems: Expands digital data handling capabilities in MCU-based designs.
  • Digital Bus Management: Uses three-state outputs to support shared bus architectures.
  • Industrial Automation: Supports digital control and signal buffering in industrial equipment.
  • Communication Equipment: Helps manage parallel digital signals and interface data.
  • Consumer Electronics: Provides data latching and logic control in electronic products.
  • Memory Interface Circuits: Temporarily stores address and data signals during digital operations.
  • Digital Logic Circuits: Supports signal synchronization and intermediate data storage.

10. Disclaimer

The information in this article is provided for general technical reference and electronic component selection. Specifications, electrical characteristics, package dimensions and product availability may differ depending on the manufacturer and ordering code.

Always consult the latest official manufacturer datasheet before PCB design, production or component replacement. Alternative components should not be considered direct replacements without verifying pin compatibility, timing performance and electrical requirements.

```

Quick RFQ Send your inquiry and our sales team will respond quickly.

Part Number
Quantity*
Price
Name*
Company*
Email*
Comments
```