GD25B64ESIGR GigaDevice | 64Mb SPI NOR Flash Memory Technical Guide
Product Technical Guide GD25B64ESIGR 64Mb SPI NOR Flash Memory Technical GuideGigaDevice 64-Mbit nonvolatile serial NOR Flash featuring an 8M × 8 memory organization, 2.7V to 3.6V supply, up to 133MHz…
- Part No.:
- GD25B64ESIGR
- Manufacturer:
- GigaDevice Semiconductor (HK) Limited
- Package:
- 8-SOIC (0.209", 5.30mm Width)
- Datasheet:
- GD25B64ESIGR.pdf
- Description:
- IC FLASH 64MBIT SPI/QUAD 8SOP
- Quantity:
-
Original Supply
Strict supplier screening and quality control support.
-
Datasheet Support
Help engineers quickly verify product specifications.
-
BOM Sourcing
Support multi-part procurement and RFQ matching.
GD25B64ESIGR GigaDevice | 64Mb SPI NOR Flash Memory Technical Guide
GigaDevice 64-Mbit nonvolatile serial NOR Flash featuring an 8M × 8 memory organization, 2.7V to 3.6V supply, up to 133MHz SPI clock operation, Single/Dual/Quad I/O support, and industrial-temperature SOP-8 packaging.
Product Introduction
The GD25B64ESIGR is a 64-Mbit serial NOR Flash memory device from GigaDevice. It provides nonvolatile storage for embedded firmware, boot code, system configuration, calibration information, and application data.
Its memory capacity is 64 megabits, equivalent to 8 megabytes, organized as 8M × 8 bits. Unlike volatile RAM, NOR Flash retains programmed information after power is removed.
The device supports standard Serial Peripheral Interface (SPI) communication together with Dual I/O and Quad I/O modes. These interface options allow compatible host controllers to transfer data using one, two, or four data lines.
The GD25B64E family supports clock frequencies up to 133MHz under the manufacturer's specified interface conditions. The supported clock frequency for a particular read command must be checked against the timing tables in the datasheet.
The GD25B64ESIGR operates from a 2.7V to 3.6V supply and is specified for an ambient operating temperature range of -40°C to +85°C.
This ordering variant is supplied in an 8-pin SOP package with a 208-mil body width, suitable for surface-mount assembly.
The combination of nonvolatile storage, high-speed serial access, and compact packaging makes the device suitable for microcontroller-based equipment, network products, industrial controllers, and consumer electronics.
Key Benefits
64Mb Nonvolatile Storage
Provides 8MB of persistent memory for firmware images, configuration data, and embedded application resources.
High-Speed Serial Access
Supports fast SPI communication and higher-throughput Dual and Quad I/O transfers with compatible host controllers.
Compact System Integration
Uses an industry-familiar eight-pin serial Flash interface and surface-mount package to reduce PCB complexity.
Flexible Data Protection
Offers software-controlled protection, security registers, and additional management functions for embedded storage.
Features
- 64-Mbit nonvolatile NOR Flash memory
- 8M × 8-bit memory organization
- 8MB total storage capacity
- 2.7V to 3.6V operating supply
- Single I/O SPI communication
- Dual I/O read support
- Quad I/O read support
- Maximum family interface frequency of 133MHz under specified conditions
- Standard serial command-based memory access
- Page-program capability
- Sector and block erase operations
- Chip erase capability
- Software reset functionality
- Program and erase suspend support
- Security registers with one-time-programmable locking features
- Unique device identification capability
- Software-controlled memory protection
- Write-enable and write-disable command support
- Status and configuration register access
- Low-power standby and power-management functionality
- Industrial ambient temperature range of -40°C to +85°C for the SI ordering option
- 8-pin 208-mil SOP package
- Surface-mount installation
- Tape-and-reel ordering format
Engineering Note: NOR Flash programming requires previously erased memory locations. Unlike F-RAM, the GD25B64ESIGR cannot repeatedly overwrite arbitrary bytes without considering erase operations, programming restrictions, and endurance limits.
Package
The GD25B64ESIGR is supplied in an 8-pin SOP package with a nominal 208-mil body width.
- Package Type: SOP-8 / SOIC-8
- Package Width: 208 mil, approximately 5.3mm
- Pin Count: 8
- Mounting Type: Surface Mount
- Operating Temperature: -40°C to +85°C
- Supply Voltage: 2.7V to 3.6V
- Packaging: Tape and Reel
- Typical Factory Reel Quantity: 2,000 pieces
- Device Family: GD25B64E
- Manufacturer: GigaDevice
The 208-mil SOP-8 package is wider than the commonly used 150-mil narrow-body SOIC-8 package. Engineers should not assume the two footprints are interchangeable.
Before PCB production, verify the official mechanical drawing, lead pitch, overall dimensions, pin-one orientation, and recommended solder land pattern.
Pinout
The GD25B64ESIGR uses a conventional eight-pin serial NOR Flash interface. Several pins have different functions depending on whether standard SPI or Quad I/O mode is selected.
| Pin | Signal | Function |
|---|---|---|
| 1 | CS# | Active-low chip-select input. |
| 2 | SO / IO1 | Serial data output in standard SPI mode; bidirectional data line 1 in Quad I/O mode. |
| 3 | WP# / IO2 | Write-protect input in applicable standard modes; data line 2 in Quad I/O mode. |
| 4 | GND | Ground reference. |
| 5 | SI / IO0 | Serial data input in standard SPI mode; bidirectional data line 0 in Quad I/O mode. |
| 6 | SCLK | Serial clock input. |
| 7 | HOLD# / RESET# / IO3 | Multiplexed hold, reset, or Quad I/O data-line function, depending on device configuration. |
| 8 | VCC | Positive supply input, 2.7V to 3.6V. |
Standard SPI Operation: The host communicates through CS#, SCLK, SI, and SO. WP# and the multiplexed HOLD#/RESET# pin must be configured correctly for the selected operating mode.
Quad I/O Operation: IO0 through IO3 carry data when the device is configured for supported Quad commands. The host must implement the correct command sequence, dummy cycles, and I/O direction changes.
Important: The exact HOLD#/RESET#/IO3 behavior is configuration-dependent. Confirm the applicable function and any required pull-up connections from the official GD25B64E datasheet before finalizing the circuit.
Specifications
| Parameter | Value |
|---|---|
| Part Number | GD25B64ESIGR |
| Manufacturer | GigaDevice |
| Product Family | GD25B64E |
| Memory Type | Nonvolatile NOR Flash |
| Memory Technology | Serial NOR Flash |
| Memory Density | 64Mbit |
| Memory Capacity | 8MB |
| Memory Organization | 8M × 8 |
| Interface | SPI / Dual I/O / Quad I/O |
| Maximum Family Clock Frequency | 133MHz, command-dependent |
| Minimum Supply Voltage | 2.7V |
| Maximum Supply Voltage | 3.6V |
| Nominal Supply Voltage | 3.3V |
| Maximum Active Read Current | 20mA, distributor-listed parameter |
| Read Interface Width | 1, 2, or 4 Data Lines |
| Memory Programming | Page Program |
| Erase Functions | Sector, Block, and Chip Erase |
| Software Reset | Supported |
| Program/Erase Suspend | Supported |
| Security Registers | Supported |
| Unique ID | Supported |
| Operating Temperature | -40°C to +85°C |
| Package | SOP-8, 208 mil |
| Pin Count | 8 |
| Mounting Type | Surface Mount |
| Packaging | Tape and Reel |
| Manufacturer Family Status | Mass Production |
Capacity: The device provides 67,108,864 bits of storage, equivalent to 8,388,608 bytes. Firmware images, configuration structures, and other stored data must fit within the available address space.
Clock Speed: GigaDevice lists 133MHz for the GD25B64E family. The maximum usable clock frequency depends on the selected SPI command, bus mode, voltage, and timing conditions.
Quad Data Throughput: Four data lines can theoretically transfer four bits per clock cycle. At 133MHz, the raw interface rate can reach 532Mbit/s, excluding command, address, dummy-cycle, and other protocol overhead.
Programming and Erasing: Flash memory writes require a write-enable operation and must follow the device's page-program and erase restrictions. Software should poll the relevant status bits or otherwise confirm operation completion.
Endurance: Program/erase endurance and retention requirements must be evaluated against the manufacturer's guaranteed conditions. Applications with frequent updates should consider wear management and appropriate data organization.
Supply Integrity: Use suitable local bypass capacitance and maintain a stable supply during program and erase operations. Power interruption during an active memory operation may compromise the affected data.
Equivalent
When evaluating a GD25B64ESIGR equivalent or replacement, engineers should compare memory density, supply voltage, SPI command compatibility, maximum frequency, erase architecture, package dimensions, and pin functions.
GD25Q64ESIGY: A related GigaDevice 64-Mbit SPI NOR Flash device identified by DigiKey as a parametric substitute. The memory capacity and interface category are similar, but command compatibility, timing, package details, and ordering status require verification.
GD25B64E Family Variants: Other GD25B64E ordering options may provide the same basic memory architecture in alternative package styles or temperature grades. Package and ordering suffixes must be reviewed before substitution.
W25Q64JV: A 64-Mbit SPI NOR Flash family from Winbond. It may be considered as a functional alternative, but JEDEC identification, supported commands, erase sizes, timing, and footprint must be compared.
MX25L6433F: A related 64-Mbit serial NOR Flash family from Macronix. Compatibility depends on the exact suffix, supply voltage, pin configuration, and firmware command implementation.
IS25LP064A: A 64-Mbit serial NOR Flash family from ISSI. It may be suitable for redesigned or qualified systems requiring similar memory capacity.
Replacement Recommendation: For an existing GD25B64ESIGR PCB, prioritize the original part or a manufacturer-approved package-compatible variant. Cross-manufacturer replacements should undergo electrical, firmware, and production qualification.
Qualification Checklist: Verify 64-Mbit capacity, 2.7V–3.6V supply, 208-mil SOP-8 footprint, SPI/Quad mode behavior, JEDEC ID, status-register bits, write-protect functions, reset behavior, erase sizes, and programming timing.
Manufacturer
GigaDevice Semiconductor is a semiconductor company specializing in Flash memory, microcontrollers, sensors, and related integrated circuits.
The GD25B64E belongs to GigaDevice's high-performance SPI NOR Flash product portfolio, designed for nonvolatile code and data storage in embedded systems.
The manufacturer lists the GD25B64E family in mass production, with 64-Mbit density, 2.7V to 3.6V operation, and Single, Dual, and Quad I/O support.
Official Product Page: GigaDevice GD25B64E
Official Documentation: The GD25B64E product page lists document DS-00602-GD25B64E-Rev1.0. Obtain the current datasheet from the manufacturer's documentation section.
Manufacturer Website: www.gigadevice.com
For purchasing, verify the complete GD25B64ESIGR ordering number, original packaging, device marking, traceability, date code, and current availability.
Applications
Embedded Firmware Storage
Stores microcontroller firmware, bootloader images, configuration data, and software resources.
Industrial Controllers
Provides nonvolatile storage for control-system firmware, operating parameters, and maintenance records.
Networking Equipment
Stores firmware and persistent configuration information in communication modules and network devices.
Consumer Electronics
Provides nonvolatile storage for device software, display resources, and user configuration settings.
Data Logging Systems
Stores event records and periodic measurement data when appropriate erase management is implemented.
IoT and Smart Devices
Supports connected products requiring external code storage, firmware updates, or persistent system settings.
Typical Application Circuit: A microcontroller or processor communicates with the GD25B64ESIGR using CS#, SCLK, and the SPI data pins. The memory device operates from a regulated 3.3V-class supply with local decoupling.
For standard SPI operation, the host uses SI and SO for command transmission and data reception. For supported Quad I/O operations, IO0 through IO3 provide higher transfer bandwidth.
Firmware Storage: The host can retrieve boot code, application firmware, or configuration data from Flash during startup. Some processors support execute-in-place or memory-mapped external Flash access when their controller and firmware architecture permit it.
Firmware Update Strategy: Systems storing update images should incorporate integrity verification, power-failure handling, and appropriate recovery procedures to avoid unusable firmware after an interrupted update.
Data Logging: NOR Flash can store persistent logs, but frequent small writes require careful page and erase-sector management. Wear leveling or circular logging may be necessary for high-update applications.
PCB Layout: Keep the SPI clock and data traces short, use a low-impedance ground reference, and place a suitable ceramic bypass capacitor close to VCC and GND. At high interface frequencies, trace impedance and signal integrity become increasingly important.
Voltage Compatibility: The GD25B64ESIGR is a 3.3V-class memory device. Do not connect 5V logic signals directly unless the interface is explicitly protected or translated to compatible voltage levels.
Disclaimer
This technical guide is provided for general product identification, engineering reference, and procurement support. All specifications, pin assignments, maximum operating frequencies, memory architecture, program and erase timing, endurance, data retention, package dimensions, environmental ratings, and lifecycle information should be verified against the latest official GigaDevice documentation before design or purchase. Interface performance depends on the selected command, bus configuration, host controller, supply voltage, PCB layout, and operating conditions. Suggested alternatives are not guaranteed direct replacements. Product prices, availability, and ordering options may change without notice.

