Home > The Posts > Product Guides > ISOW7742QDFMRQ1 Texas Instruments | Automotive 4-Channel Digital Isolator
ISOW7742QDFMRQ1 - Texas Instruments

ISOW7742QDFMRQ1 Texas Instruments | Automotive 4-Channel Digital Isolator

Product Technical Guide ISOW7742QDFMRQ1 Automotive 4-Channel Digital Isolator Technical GuideTexas Instruments automotive-qualified, reinforced digital isolator featuring four isolation channels in a 2…

In Stock 475 Available Inventory
Part No.:
ISOW7742QDFMRQ1
Manufacturer:
Texas Instruments
Package:
20-SOIC (0.295", 7.50mm Width)
Datasheet:
ISOW7742QDFMRQ1.pdf
Description:
AUTOMOTIVE, LOW-EMISSIONS, QUAD-
Quantity:
Original Supply

Strict supplier screening and quality control support.

Datasheet Support

Help engineers quickly verify product specifications.

BOM Sourcing

Support multi-part procurement and RFQ matching.

ISOW7742QDFMRQ1 Texas Instruments | Automotive 4-Channel Digital Isolator

Product Technical Guide
ISOW7742QDFMRQ1 Automotive 4-Channel Digital Isolator Technical Guide

Texas Instruments automotive-qualified, reinforced digital isolator featuring four isolation channels in a 2-forward/2-reverse configuration, an integrated low-emissions DC/DC converter, 100Mbps data transmission, 5000Vrms isolation withstand rating, and a 20-pin wide-body SOIC package.

Part NumberISOW7742QDFMRQ1
ManufacturerTexas Instruments
Device TypeReinforced Digital Isolator with Integrated Power
01

Product Introduction

The ISOW7742QDFMRQ1 is an automotive-qualified, reinforced, four-channel digital isolator manufactured by Texas Instruments. It combines high-speed galvanic signal isolation with an integrated isolated DC/DC power converter, reducing the need for a separate isolated power module in compact electronic designs.

The device provides four unidirectional isolation channels arranged as two forward channels and two reverse channels. This configuration supports bidirectional communication at the system level while maintaining galvanic separation between two electrical domains.

With a maximum data rate of 100Mbps, the ISOW7742QDFMRQ1 supports high-speed digital control and communication signals in automotive electronics, power conversion systems, and embedded control equipment.

The integrated low-emissions DC/DC converter delivers up to 550mW of isolated output power. It provides selectable 3.3V or 5V isolated output voltage, depending on the VSEL connection and supported operating conditions.

The device supports independent supply domains for the isolation logic and power converter. Its logic supply operates from 1.71V to 5.5V, while the power converter supports nominal 3.3V and 5V input supplies.

The ISOW7742-Q1 family offers a 5000Vrms isolation withstand rating, a 1000Vrms working isolation voltage rating, and a minimum common-mode transient immunity of 85kV/µs.

The device is AEC-Q100 qualified for automotive applications and operates across an ambient temperature range of -40°C to +125°C.

The ISOW7742QDFMRQ1 is supplied in a 20-pin DFM wide-body SOIC package, supporting applications that require reinforced isolation, integrated power, and robust electromagnetic compatibility.

02

Key Benefits

Reinforced Galvanic Isolation

Provides high-voltage isolation between control and power domains, with a 5000Vrms isolation withstand rating.

Integrated Isolated Power

Delivers up to 550mW of isolated power, reducing the need for a separate isolated DC/DC converter.

100Mbps Data Transmission

Four digital channels support fast signal transfer with two forward and two reverse communication paths.

Automotive Qualification

AEC-Q100 Grade 1 qualification supports automotive systems operating from -40°C to +125°C.

03

Features

  • Automotive-qualified reinforced digital isolator
  • AEC-Q100 Grade 1 qualification
  • Four independent digital isolation channels
  • Two forward and two reverse signal channels
  • Maximum data rate of 100Mbps
  • Integrated low-noise, low-emissions isolated DC/DC converter
  • Up to 550mW isolated output power
  • Selectable 3.3V or 5V isolated output voltage
  • Logic supply voltage range from 1.71V to 5.5V
  • Power converter input supporting nominal 3.3V and 5V operation
  • 5000Vrms isolation withstand rating
  • 1000Vrms working isolation voltage
  • 10000V peak surge isolation voltage
  • Minimum CMTI of 85kV/µs
  • Typical CMTI of 100kV/µs
  • Low-noise power converter operating at approximately 25MHz
  • Low isolated output ripple, approximately 24mV under specified conditions
  • Emission-optimized architecture for automotive EMC design
  • Power converter soft-start and fault monitoring
  • Overload and short-circuit protection
  • Thermal shutdown protection
  • Programmable isolated output voltage selection
  • Active-high channel output enable controls
  • High default output state for the non-F device variant
  • 20-pin wide-body SOIC package
  • Operating temperature range from -40°C to +125°C

Design Note: The integrated DC/DC converter reduces the number of isolated power components, but external bypass capacitors, suitable PCB layout, and recommended connections between VISOOUT and VISOIN remain necessary.

04

Package

The ISOW7742QDFMRQ1 is supplied in the Texas Instruments DFM 20-pin wide-body SOIC package, designed to provide physical separation between the primary and secondary isolation domains.

  • Package Type: Wide-Body SOIC
  • Package Code: DFM
  • Pin Count: 20
  • Mounting Type: Surface Mount
  • Nominal Package Size: 12.83mm × 10.30mm including leads
  • Nominal Body Size: 12.83mm × 7.5mm
  • Packaging: Tape and Reel
  • Standard Reel Quantity: 850 pieces
  • Moisture Sensitivity Level: MSL 3
  • Peak Reflow Temperature: 260°C
  • Lead Finish: NiPdAu
  • RoHS Compliance: Yes
  • REACH Compliance: Yes

The wide-body package helps support the creepage and clearance requirements associated with reinforced isolation applications.

PCB layout must preserve the isolation barrier between the primary and secondary domains. Designers should follow the manufacturer's recommended spacing, grounding, decoupling, and EMI mitigation practices.

Where appropriate, ferrite beads can be used in the isolated supply connections to reduce conducted emissions and improve noise performance.

05

Pinout

The ISOW7742QDFMRQ1 pinout contains four digital isolation channels, primary-side and secondary-side supply connections, output-enable controls, isolated voltage selection, and power converter monitoring.

Pin Signal Function
1 VIO Primary-side digital logic supply.
2 INA Digital input channel A.
3 INB Digital input channel B.
4 OUTC Digital output channel C.
5 OUTD Digital output channel D.
6 GNDIO Primary-side logic ground.
7 EN_IO1 Primary-side output enable control.
8 EN/FLT Power converter enable or fault indication.
9 VDD Primary-side DC/DC converter power supply.
10 GND1 Primary-side DC/DC converter ground.
11 GND2 Isolated DC/DC converter output ground.
12 VISOOUT Isolated DC/DC converter voltage output.
13 VSEL Isolated output voltage selection input.
14 EN_IO2 Secondary-side output enable control.
15 GISOIN Secondary-side digital logic ground.
16 IND Digital input channel D.
17 INC Digital input channel C.
18 OUTB Digital output channel B.
19 OUTA Digital output channel A.
20 VISOIN Secondary-side digital logic supply.
Pins 2, 3, 18 and 19 – Forward ChannelsINA and INB transfer digital signals across the isolation barrier to OUTA and OUTB.
Pins 4, 5, 16 and 17 – Reverse ChannelsINC and IND transfer signals from the secondary side to OUTC and OUTD on the primary side.
Pins 1 and 9 – VIO / VDDIndependent primary-side supplies for digital logic and the integrated DC/DC converter.
Pins 12 and 20 – VISOOUT / VISOINIsolated power output and secondary-side logic supply connections.
Pins 6 and 10 – GNDIO / GND1Primary-side ground connections that must be connected together on the PCB.
Pins 11 and 15 – GND2 / GISOINSecondary-side ground connections, joined directly or through the recommended filtering arrangement.
Pin 8 – EN/FLTMultifunction power converter enable input or active-low fault output.
Pin 13 – VSELSelects the isolated output voltage: 5V when connected to VISOOUT or 3.3V when connected to GND2.

Important: These pin assignments apply specifically to the ISOW7742-Q1 20-pin DFM package. The ISOW7741-Q1 has a different channel-direction configuration and different assignments for the C-channel connections.

When EN_IO1 or EN_IO2 is low, the corresponding outputs are placed in a high-impedance state and associated transmitters are disabled. The EN/FLT pin must be configured according to its intended operating mode.

06

Specifications

Parameter Value
Part Number ISOW7742QDFMRQ1
Manufacturer Texas Instruments
Product Family ISOW7742-Q1
Device Type Reinforced Digital Isolator with Integrated DC/DC Converter
Automotive Qualification AEC-Q100 Grade 1
Number of Isolation Channels 4
Forward Channels 2
Reverse Channels 2
Maximum Data Rate 100Mbps
Logic Supply Voltage (VIO) 1.71V to 5.5V, within specified operating ranges
Power Converter Supply (VDD) 2.97V to 3.63V or 4.5V to 5.5V
Selectable Isolated Output Voltage 3.3V or 5V
Maximum Isolated Output Power 550mW
Maximum Isolated Load Current, 5V to 5V 110mA
Maximum Isolated Load Current, 5V to 3.3V 140mA
Maximum Isolated Load Current, 3.3V to 3.3V 60mA
Power Converter Efficiency at Maximum Load 46% under specified conditions
Power Converter Frequency Approximately 25MHz
Isolated Output Ripple 24mV under specified conditions
Isolation Rating Reinforced
Isolation Withstand Voltage (VISO) 5000Vrms
Working Isolation Voltage (VIOWM) 1000Vrms
Surge Isolation Voltage (VIOSM) 10000V peak
Transient Isolation Voltage (VIOTM) 7071V peak
Minimum CMTI 85kV/µs
Typical CMTI 100kV/µs
Default Output State High, non-F variant
Power Converter Enable / Fault EN/FLT multifunction pin
Channel Output Enable EN_IO1 and EN_IO2
Operating Ambient Temperature -40°C to +125°C
Package Type Wide-Body SOIC
Package Code DFM
Pin Count 20
Mounting Type Surface Mount
Packaging Quantity 850 pieces per reel
Moisture Sensitivity Level MSL 3
RoHS Compliance Yes
REACH Compliance Yes
Product Status ACTIVE

Isolation Performance: The 5000Vrms rating describes a specified isolation withstand test. It is not the permissible continuous operating voltage. The maximum working isolation voltage is separately specified as 1000Vrms under the applicable insulation conditions.

Power Converter Operation: The integrated converter can generate an isolated 3.3V or 5V supply. Available output current depends on the input and output voltage configuration and operating conditions.

Logic Supply Flexibility: VIO and VDD may be supplied independently, allowing low-voltage digital logic to interface with the isolation channels while the power converter operates from a suitable 3.3V or 5V supply.

EMC Considerations: The low-emissions architecture supports automotive EMC design. However, system-level CISPR 25 compliance depends on PCB layout, filtering, grounding, shielding, and the complete electronic assembly.

Safety Considerations: Reinforced isolation performance depends on the device rating, PCB creepage and clearance, insulation coordination, operating environment, and relevant safety standards.

07

Equivalent

When selecting an ISOW7742QDFMRQ1 equivalent or replacement, engineers should compare the channel direction, insulation rating, integrated isolated power capability, data rate, output default state, package, pinout, and automotive qualification.

ISOW7742FQDFMRQ1: A closely related automotive-grade device with the same 2-forward/2-reverse channel arrangement and integrated power. The F version has a default-low output state rather than the default-high behavior of ISOW7742QDFMRQ1. It is not a behaviorally identical replacement.

ISOW7741QDFMRQ1: A related automotive digital isolator with integrated power. It uses a different forward/reverse channel configuration and is not directly interchangeable without reviewing signal routing and channel direction.

ISOW7742: A related non-Q1 device in the same broader family. Automotive qualification and product-specific insulation documentation must be considered before substitution.

ISOW6442: A newer Texas Instruments digital isolator family with integrated power and different electrical and package characteristics. It may be considered for a redesigned system, but is not a direct pin-compatible replacement.

Discrete Isolator and Isolated DC/DC Combination: A separate four-channel digital isolator paired with an isolated power converter can provide a functional alternative. This approach requires additional PCB area, component selection, EMI design, and isolation coordination.

Replacement Recommendation: For an existing automotive PCB, prioritize the exact ISOW7742QDFMRQ1 ordering number. Any alternative should be evaluated for channel direction, fail-safe behavior, power output, isolation certifications, EMC characteristics, temperature rating, and PCB compatibility.

08

Manufacturer

Texas Instruments Incorporated is a global semiconductor manufacturer specializing in analog integrated circuits, embedded processing, power management, and interface technologies.

The ISOW7742-Q1 belongs to the company's portfolio of automotive isolation products designed for electronic systems requiring high-voltage separation, digital signal integrity, and integrated isolated power.

The device is designed for applications where electromagnetic compatibility, insulation performance, and reduced component count are important engineering requirements.

Official Product Page: ISOW7742-Q1 – Texas Instruments

Official Ordering Information: ISOW7742QDFMRQ1 Part Details

Official Datasheet: ISOW774x-Q1 Digital Isolator Datasheet

Manufacturer Website: www.ti.com

For procurement, confirm the original manufacturer, complete ordering number, packaging quantity, lot traceability, automotive qualification, and product documentation.

09

Applications

Electric Vehicle Battery Management

Galvanic isolation of control and monitoring signals between battery management circuits and associated electronic control domains.

On-Board Chargers

High-speed isolated digital communication and auxiliary isolated power for automotive charging system control circuitry.

Traction Inverters

Digital signal isolation between control processors and high-voltage power conversion circuitry.

Automotive DC/DC Converters

Reinforced signal isolation and integrated auxiliary power for control and monitoring circuits in vehicle power converters.

Embedded Control Interfaces

Isolated communication between microcontrollers, sensors, and digital control circuits operating in separate electrical domains.

High-Voltage Monitoring Systems

Electrical isolation for digital control and status signals in high-voltage electronic assemblies.

Application Note: In an automotive power conversion design, the primary-side controller can communicate with an isolated secondary-side controller through the four digital channels. The integrated converter supplies auxiliary power to the isolated domain, subject to its output power and current limitations.

The primary-side GNDIO and GND1 pins must be connected together on the PCB. On the secondary side, GND2 and GISOIN must be connected according to the manufacturer's recommended filtering arrangement. The primary and secondary ground domains must remain galvanically separated.

VISOOUT and VISOIN require an appropriate external connection, such as a direct link or recommended ferrite-bead arrangement. Suitable decoupling capacitors and isolation spacing must be incorporated into the final PCB design.

Safety Warning: The ISOW7742QDFMRQ1 is an isolation component, not a complete high-voltage safety system. System designers must independently verify insulation coordination, creepage, clearance, protective measures, thermal limits, and compliance with the applicable automotive and electrical safety standards.

10

Disclaimer

This technical guide is provided for general product identification, engineering reference, and procurement support. Specifications, isolation ratings, channel directions, pin assignments, output power, operating conditions, package dimensions, safety certifications, automotive qualification, and lifecycle status should be verified against the latest Texas Instruments documentation before design or purchase. Isolation ratings are subject to defined test conditions and must not be interpreted as unrestricted continuous working voltages. Suggested alternatives are not guaranteed direct replacements. Product prices and availability may change without notice.

Quick RFQ Send your inquiry and our sales team will respond quickly.

Part Number
Quantity*
Price
Name*
Company*
Email*
Comments
```