Home > The Posts > Product Guides > LM324DR Quad Operational Amplifier Technical Guide
LM324DR - Texas Instruments

LM324DR Quad Operational Amplifier Technical Guide

Product Technical Guide LM324DR Quad Operational Amplifier Technical GuideTexas Instruments general-purpose quad operational amplifier featuring four independent amplifiers, 3V to 30V total supply oper…

In Stock 587,669 Available Inventory
Part No.:
LM324DR
Manufacturer:
Texas Instruments
Package:
14-SOIC (0.154", 3.90mm Width)
Datasheet:
LM324DR.pdf
Description:
IC OP AMP 4CH 14-SOIC
Quantity:
Original Supply

Strict supplier screening and quality control support.

Datasheet Support

Help engineers quickly verify product specifications.

BOM Sourcing

Support multi-part procurement and RFQ matching.

LM324DR Quad Operational Amplifier Technical Guide

Product Technical Guide
LM324DR Quad Operational Amplifier Technical Guide

Texas Instruments general-purpose quad operational amplifier featuring four independent amplifiers, 3V to 30V total supply operation, 1.2MHz typical gain-bandwidth product, 0.5V/µs typical slew rate, and 14-pin SOIC packaging.

Part NumberLM324DR
ManufacturerTexas Instruments
Device TypeQuad Operational Amplifier
01

Product Introduction

The LM324DR is a general-purpose quadruple operational amplifier manufactured by Texas Instruments. It integrates four independent, internally frequency-compensated operational amplifiers in a single 14-pin SOIC package.

The device is designed for applications requiring multiple analog signal-processing stages with relatively low power consumption. Its four amplifier channels can be configured independently for signal amplification, buffering, filtering, voltage sensing, and other analog functions.

One of the primary advantages of the LM324DR is its ability to operate from a single positive supply. The specified total supply voltage range is 3V to 30V, making it suitable for a variety of low-voltage and industrial electronic systems. It can also operate from split supplies when the total voltage remains within the specified range.

The input common-mode voltage range includes the negative supply rail, allowing the amplifier to process signals near ground in single-supply configurations. This characteristic is useful in low-side sensing and ground-referenced measurement circuits.

With a typical gain-bandwidth product of 1.2MHz and a typical slew rate of 0.5V/µs, the LM324DR is appropriate for low-frequency and moderate-speed analog signal processing rather than high-speed precision applications.

The LM324DR is supplied in a 14-pin SOIC package with tape-and-reel packaging for automated assembly. Its specified operating ambient temperature range is 0°C to +70°C.

The LM324 family remains widely used in established analog designs, educational circuits, industrial electronics, and cost-sensitive applications where dependable general-purpose amplification is required.

02

Key Benefits

Four Amplifiers in One Package

Integrates four independent operational amplifiers to reduce component count and PCB area in multistage analog circuits.

Flexible Supply Operation

Supports 3V to 30V total supply operation with single-supply or appropriately configured split-supply circuits.

Ground-Sensing Input Range

Input common-mode range includes the negative supply rail, supporting ground-referenced analog measurements.

General-Purpose Circuit Design

Unity-gain-stable amplifiers support buffering, active filtering, amplification, and signal-conditioning functions.

03

Features

  • Four independent operational amplifiers
  • Internally frequency-compensated architecture
  • Unity-gain stable operation
  • Single-supply or split-supply capability
  • 3V to 30V total supply voltage range
  • 1.2MHz typical gain-bandwidth product
  • 0.5V/µs typical slew rate
  • Input common-mode range includes the negative supply rail
  • Typical input offset voltage of approximately 3mV
  • Maximum input offset voltage of 7mV at 25°C
  • Typical quiescent current of approximately 175µA per amplifier
  • Typical common-mode rejection ratio of 80dB
  • Typical input voltage noise density of 35nV/√Hz at 1kHz
  • Low output-voltage swing toward the negative supply under suitable loading
  • Four separately accessible amplifier outputs
  • Standard 14-pin quad op-amp pin arrangement
  • 14-pin SOIC surface-mount package
  • Commercial operating temperature range of 0°C to +70°C
  • Tape-and-reel packaging
  • RoHS-compliant ordering option

Engineering Note: The LM324DR is not a fully rail-to-rail operational amplifier. Its input common-mode range extends to the negative supply, but the positive input range and high-level output swing require headroom below the positive supply rail.

04

Package

The LM324DR uses the Texas Instruments SOIC-14 package, identified by the package code D.

  • Package Type: SOIC
  • Package Code: D
  • Pin Count: 14
  • Nominal Body Size: 8.65mm × 3.9mm
  • Nominal Lead Pitch: 1.27mm
  • Mounting Type: Surface Mount
  • Packaging: Large Tape and Reel
  • Standard Reel Quantity: 2,500 pieces
  • Moisture Sensitivity Level: MSL 1
  • Peak Reflow Temperature: 260°C
  • Lead Finish: NiPdAu
  • RoHS Compliance: Yes
  • Product Status: ACTIVE

The SOIC-14 package provides a widely supported footprint for analog circuitry. Its 1.27mm lead pitch is compatible with conventional surface-mount assembly processes.

For PCB manufacturing, verify the package outline, recommended land pattern, pin-one orientation, and soldering requirements using the latest TI mechanical drawing.

05

Pinout

The LM324DR pinout follows the standard 14-pin quad operational amplifier arrangement, with four amplifier channels sharing a common positive and negative supply.

Pin Signal Function
1 1OUT Output of amplifier 1.
2 1IN− Inverting input of amplifier 1.
3 1IN+ Non-inverting input of amplifier 1.
4 VCC+ Positive supply voltage.
5 2IN+ Non-inverting input of amplifier 2.
6 2IN− Inverting input of amplifier 2.
7 2OUT Output of amplifier 2.
8 3OUT Output of amplifier 3.
9 3IN− Inverting input of amplifier 3.
10 3IN+ Non-inverting input of amplifier 3.
11 VCC− Negative supply voltage or ground in single-supply operation.
12 4IN+ Non-inverting input of amplifier 4.
13 4IN− Inverting input of amplifier 4.
14 4OUT Output of amplifier 4.
Amplifier 1 – Pins 1, 2, 3Output, inverting input, and non-inverting input.
Amplifier 2 – Pins 5, 6, 7Non-inverting input, inverting input, and output.
Amplifier 3 – Pins 8, 9, 10Output, inverting input, and non-inverting input.
Amplifier 4 – Pins 12, 13, 14Non-inverting input, inverting input, and output.
Pin 4 – VCC+Positive supply connection.
Pin 11 – VCC−Negative supply or ground reference.

Single-Supply Configuration: Connect pin 4 to the positive supply and pin 11 to ground. The input and output signals must remain within the applicable common-mode and output-swing limits.

Split-Supply Configuration: Connect pin 4 to the positive rail and pin 11 to the negative rail. The total voltage between these pins must remain within the specified supply range.

Unused Amplifiers: Do not leave unused amplifier inputs floating. Configure unused channels in a stable closed-loop arrangement with an appropriate reference voltage within the valid input common-mode range.

06

Specifications

Parameter Value
Part Number LM324DR
Manufacturer Texas Instruments
Device Type Quad Operational Amplifier
Amplifier Channels 4
Amplifier Architecture Bipolar
Minimum Total Supply Voltage 3V
Maximum Total Supply Voltage 30V
Typical Gain-Bandwidth Product 1.2MHz
Typical Slew Rate 0.5V/µs
Maximum Input Offset Voltage at 25°C 7mV
Typical Input Offset Voltage 3mV
Typical Quiescent Current per Channel 0.175mA
Maximum Input Bias Current at 25°C 250nA
Typical Common-Mode Rejection Ratio 80dB
Typical Input Voltage Noise at 1kHz 35nV/√Hz
Typical Output Current Capability 40mA (application- and condition-dependent)
Input Common-Mode Range Includes Negative Supply Rail
Positive Input Common-Mode Headroom Approximately 1.5V Typical
Output Swing Not Fully Rail-to-Rail
Unity-Gain Stable Yes
Operating Temperature Range 0°C to +70°C
Package Type SOIC-14
Package Code D
Pin Count 14
Mounting Type Surface Mount
Packaging Tape and Reel
Standard Reel Quantity 2,500
RoHS Compliance Yes
Product Status ACTIVE

Bandwidth: The typical 1.2MHz gain-bandwidth product represents the approximate relationship between closed-loop gain and small-signal bandwidth. For example, a closed-loop gain of 10 generally provides substantially less bandwidth than a unity-gain configuration.

Slew Rate: The typical 0.5V/µs slew rate limits how quickly the amplifier output can change. Large-amplitude or high-frequency signals may experience slew-rate distortion.

Input Voltage Range: The input common-mode range includes the negative supply rail but does not extend fully to the positive supply. The valid upper limit is approximately VCC+ minus 1.5V at 25°C and may require additional headroom across temperature.

Output Swing: The output can approach the negative rail under suitable load conditions. However, it cannot generally swing all the way to the positive rail, especially under heavier loading.

Offset and Bias Current: Input offset voltage and input bias current contribute to DC measurement errors. Precision circuits should evaluate resistor values, gain, source impedance, and temperature-related drift.

Temperature Rating: The LM324DR is specified for 0°C to +70°C. Applications requiring an extended industrial temperature range should consider appropriately rated alternatives.

07

Equivalent

When selecting an LM324DR equivalent or replacement, engineers should compare the amplifier count, pinout, supply voltage, operating temperature, input common-mode range, output swing, bandwidth, slew rate, offset voltage, and package dimensions.

LM324B: Texas Instruments identifies the LM324B as a next-generation drop-in upgrade for the LM324 family. It provides improved offset performance, a wider 3V to 36V supply range, and an extended operating temperature range. Choose the matching SOIC-14 ordering option for PCB compatibility.

LM324BA: A higher-accuracy version of the LM324B family, offering improved input offset specifications. It is suitable for designs requiring tighter DC accuracy while maintaining the familiar quad amplifier architecture.

LM2902: A related quad operational amplifier family with a similar standard pin arrangement. The operating temperature, electrical specifications, and exact ordering package must be checked before substitution.

LM2902B: A newer quad amplifier option offering improved electrical characteristics and extended temperature capability. It can be considered when an updated design requires greater environmental flexibility.

LM324A: A related LM324 family variant. Verify the package and grade-specific electrical limits before using it as a substitute.

LM358: A dual operational amplifier sharing similar general-purpose circuit characteristics, but containing only two amplifiers. It is not a pin-compatible replacement for the quad LM324DR.

Replacement Recommendation: For an existing LM324DR PCB, the corresponding SOIC-14 LM324B ordering option is a strong upgrade candidate because TI explicitly identifies the B family as a drop-in replacement. Nevertheless, review the updated device's behavior under the actual supply, loading, and signal conditions.

08

Manufacturer

Texas Instruments Incorporated is a global semiconductor manufacturer specializing in analog integrated circuits, embedded processing, power management, and signal-chain products.

The LM324 is part of TI's established operational amplifier portfolio and is widely used in general-purpose analog electronics.

The LM324DR ordering number identifies the SOIC-14, tape-and-reel configuration of the LM324.

Texas Instruments currently identifies LM324DR as an ACTIVE product and recommends the newer LM324B family for designs seeking improved performance.

Official Product Page: Texas Instruments LM324

Official Ordering Information: LM324DR Product Details

Official Datasheet: LM324 Family Datasheet

Manufacturer Website: www.ti.com

For procurement, verify the complete part number, manufacturer markings, original packaging, lot traceability, moisture sensitivity classification, and current product lifecycle status.

09

Applications

Industrial Control

Analog amplification, threshold detection, and signal conditioning in industrial control boards and monitoring equipment.

Voltage Monitoring

Processing divided-down voltage signals for supply supervision, battery measurement, and general analog monitoring.

Active Analog Filters

Implementing low-pass, high-pass, and band-pass filters for low-frequency sensor and control signals.

Sensor Signal Conditioning

Amplifying and buffering outputs from resistive sensors, transducers, and other analog sensing elements.

Audio and Control Circuits

General low-frequency signal amplification and control-voltage processing where bandwidth and distortion requirements are compatible.

Test and Measurement

Building analog front ends, buffer stages, and basic signal-processing circuits in laboratory and educational equipment.

Typical Non-Inverting Amplifier: An analog signal is applied to the non-inverting input of one amplifier. A feedback resistor network connects the output to the inverting input and establishes the desired closed-loop gain.

For a standard non-inverting amplifier, the ideal gain is approximately 1 + Rf/Rg, where Rf is the feedback resistor and Rg connects the inverting input to the reference node. Actual circuit behavior depends on bandwidth, offset, input range, output swing, and loading.

Voltage-Follower Application: Connect the amplifier output to its inverting input and apply the signal to the non-inverting input. This unity-gain configuration provides buffering, subject to the device's valid input and output voltage ranges.

Sensor Interface: Multiple amplifier channels can independently condition sensor signals before they reach a microcontroller ADC. Designers should verify that each amplifier output remains within the ADC input range.

Active Filter Design: The LM324DR can implement low-frequency active filters using resistors and capacitors. The selected cutoff frequency should allow sufficient bandwidth margin relative to the amplifier's 1.2MHz typical gain-bandwidth product.

Comparator Consideration: Although operational amplifiers are sometimes used for basic threshold detection, the LM324DR is not a dedicated comparator. Applications requiring fast switching, defined hysteresis, or reliable recovery from saturation should use an appropriate comparator.

PCB Layout: Place a suitable bypass capacitor close to the supply pins, maintain short feedback paths, minimize noise coupling into high-impedance inputs, and use a stable reference or ground connection.

Design Limitation: The LM324DR is not recommended for high-speed, high-precision, or rail-to-rail applications without confirming that its electrical performance satisfies the complete system requirements.

10

Disclaimer

This technical guide is provided for general product identification, engineering reference, and procurement support. All specifications, pin assignments, operating voltage limits, input common-mode requirements, output swing characteristics, temperature ratings, package dimensions, compliance information, and lifecycle status should be verified against the latest Texas Instruments documentation before design or purchase. Typical performance values are not guaranteed limits unless expressly stated by the manufacturer. Suggested alternatives are not guaranteed direct replacements under every operating condition. Actual circuit performance depends on supply voltage, component tolerances, feedback design, loading, PCB layout, and environmental conditions. Prices and availability may change without notice.

Quick RFQ Send your inquiry and our sales team will respond quickly.

Part Number
Quantity*
Price
Name*
Company*
Email*
Comments
```