SN74ALVC164245DGGR Datasheet, Pinout, Equivalent & Applications
Logic ICs & Voltage Level Translators SN74ALVC164245DGGR 16-Bit Dual-Supply Bus TransceiverThe SN74ALVC164245DGGR is a 16-bit dual-supply non-inverting bus transceiver manufactured by Texas Instruments…
- Part No.:
- SN74ALVC164245DGGR
- Manufacturer:
- Texas Instruments
- Package:
- Datasheet:
- SN74ALVC164245DGGR.pdf
- Description:
- IC TRANSLATOR BIDIR 48TSSOP
- Quantity:
-
Original Supply
Strict supplier screening and quality control support.
-
Datasheet Support
Help engineers quickly verify product specifications.
-
BOM Sourcing
Support multi-part procurement and RFQ matching.
SN74ALVC164245DGGR Datasheet, Pinout, Equivalent & Applications
SN74ALVC164245DGGR 16-Bit Dual-Supply Bus Transceiver
The SN74ALVC164245DGGR is a 16-bit dual-supply non-inverting bus transceiver manufactured by Texas Instruments. It supports bidirectional voltage translation between 2.5V, 3.3V, and 5V digital systems, featuring independent direction control, three-state outputs, and high-speed data transmission.
1. Product Introduction
The SN74ALVC164245DGGR is a 16-bit dual-supply non-inverting bus transceiver developed by Texas Instruments (TI). It belongs to the ALVC logic family and is designed for high-speed digital communication and voltage translation between different logic voltage domains.
Modern electronic systems frequently combine processors, microcontrollers, memory devices, communication interfaces, and peripheral components operating at different logic voltages. Directly connecting these devices can create signal compatibility problems. The SN74ALVC164245DGGR addresses this challenge by providing bidirectional voltage translation between compatible 2.5V, 3.3V, and 5V logic systems.
The device integrates two independent 8-bit bus transceivers, providing a total of 16 data channels. Each section has its own direction-control and output-enable signals, allowing the two groups to operate independently.
The A-side supply, VCCA, supports 2.5V and 3.3V operation, while the B-side supply, VCCB, supports 3.3V and 5V operation. This architecture enables translation from 2.5V to 3.3V, 3.3V to 2.5V, 3.3V to 5V, and 5V to 3.3V, subject to the specified operating conditions.
The SN74ALVC164245DGGR also features three-state outputs. When the output-enable function disables a channel group, its outputs enter a high-impedance state. This is particularly useful in shared bus architectures where multiple devices need to access the same data lines.
With a maximum propagation delay of 5.8ns at 3.3V and output drive capability of ±24mA at 3.3V, the device is suitable for high-speed digital interfaces. Its 48-pin TSSOP package provides an integrated solution for applications requiring multiple signal connections and reliable voltage translation.
2. Key Benefits
- 16-Bit Data Transmission: Integrates two independent 8-bit bus transceivers to support 16-bit digital data communication.
- Dual-Supply Architecture: Uses separate A-side and B-side power supplies to support different logic voltage domains.
- Bidirectional Voltage Translation: Supports communication between compatible 2.5V, 3.3V, and 5V logic systems.
- Independent Channel Control: Each 8-bit section has separate direction and output-enable controls.
- Three-State Outputs: Provides high-impedance output operation for shared bus applications.
- High-Speed Performance: Offers a maximum propagation delay of 5.8ns at 3.3V.
- Strong Output Drive: Provides ±24mA output drive capability at 3.3V under specified conditions.
- Low Static Power Consumption: ALVC technology supports efficient digital signal transmission.
- Wide Application Compatibility: Suitable for processors, memory interfaces, communication equipment, and industrial electronics.
3. Features
The SN74ALVC164245DGGR combines high-speed bus communication with flexible voltage translation and output control.
Core Logic Features
- 16-bit non-inverting bus transceiver.
- Two independent 8-bit transceiver sections.
- Bidirectional data transmission.
- Independent direction-control inputs: 1DIR and 2DIR.
- Independent output-enable inputs: 1OE and 2OE.
- Three-state output capability.
- Asynchronous bus communication.
Voltage Translation Features
- A-side supply voltage: 2.5V or 3.3V.
- B-side supply voltage: 3.3V or 5V.
- Supports 2.5V-to-3.3V signal translation.
- Supports 3.3V-to-5V signal translation.
- Supports reverse-direction translation under compatible conditions.
- Control input logic thresholds are referenced to VCCA.
Electrical Performance
- Maximum propagation delay of 5.8ns at 3.3V.
- Maximum data rate of 300Mbps according to TI product specifications.
- ±24mA output drive at 3.3V.
- High-speed ALVC logic technology.
- Latch-up performance exceeds 250mA per JESD 17.
- Operating temperature range from -40°C to +85°C.
These characteristics make the device useful in systems where high-speed parallel data transmission and voltage compatibility are both important.
4. Package
The SN74ALVC164245DGGR uses a 48-pin Thin Shrink Small Outline Package (TSSOP), identified by Texas Instruments package code DGG.
- Package Type: TSSOP
- Package Code: DGG
- Number of Pins: 48
- Body Dimensions: Approximately 12.5mm × 8.1mm
- Mounting Type: Surface Mount
- Operating Temperature: -40°C to +85°C
- Packaging: Tape and Reel
- Standard Reel Quantity: 2,000 pieces
The TSSOP-48 package provides 48 electrical connections for the two data buses, supply rails, direction controls, output enables, and ground connections.
Its surface-mount construction makes it suitable for multilayer PCBs used in industrial control equipment, embedded systems, communication devices, and computer peripherals.
For PCB design and assembly, engineers should consult the official TI package drawing for exact lead dimensions, recommended land patterns, soldering conditions, and mechanical tolerances.
5. Pinout
The SN74ALVC164245DGGR contains 48 pins organized around two independent 8-bit transceiver sections. The device includes A-side and B-side data terminals, two direction-control inputs, two output-enable inputs, dual supply connections, and ground pins.
Pin Configuration
| Pin | Symbol | Description |
|---|---|---|
| 1 | 1DIR | Direction control for section 1 |
| 2 | 1B1 | Section 1 B-side data input/output 1 |
| 3 | 1B2 | Section 1 B-side data input/output 2 |
| 4 | GND | Ground |
| 5 | 1B3 | Section 1 B-side data input/output 3 |
| 6 | 1B4 | Section 1 B-side data input/output 4 |
| 7 | VCCB | B-side supply voltage |
| 8 | 1B5 | Section 1 B-side data input/output 5 |
| 9 | 1B6 | Section 1 B-side data input/output 6 |
| 10 | GND | Ground |
| 11 | 1B7 | Section 1 B-side data input/output 7 |
| 12 | 1B8 | Section 1 B-side data input/output 8 |
| 13 | 2B1 | Section 2 B-side data input/output 1 |
| 14 | 2B2 | Section 2 B-side data input/output 2 |
| 15 | GND | Ground |
| 16 | 2B3 | Section 2 B-side data input/output 3 |
| 17 | 2B4 | Section 2 B-side data input/output 4 |
| 18 | VCCB | B-side supply voltage |
| 19 | 2B5 | Section 2 B-side data input/output 5 |
| 20 | 2B6 | Section 2 B-side data input/output 6 |
| 21 | GND | Ground |
| 22 | 2B7 | Section 2 B-side data input/output 7 |
| 23 | 2B8 | Section 2 B-side data input/output 8 |
| 24 | 2DIR | Direction control for section 2 |
| 25 | 2OE | Active-LOW output enable for section 2 |
| 26 | 2A7 | Section 2 A-side data input/output 7 |
| 27 | 2A6 | Section 2 A-side data input/output 6 |
| 28 | GND | Ground |
| 29 | 2A5 | Section 2 A-side data input/output 5 |
| 30 | 2A4 | Section 2 A-side data input/output 4 |
| 31 | VCCA | A-side supply voltage |
| 32 | 2A3 | Section 2 A-side data input/output 3 |
| 33 | 2A2 | Section 2 A-side data input/output 2 |
| 34 | GND | Ground |
| 35 | 2A1 | Section 2 A-side data input/output 1 |
| 36 | 1A8 | Section 1 A-side data input/output 8 |
| 37 | 1A7 | Section 1 A-side data input/output 7 |
| 38 | GND | Ground |
| 39 | 1A6 | Section 1 A-side data input/output 6 |
| 40 | 1A5 | Section 1 A-side data input/output 5 |
| 41 | VCCA | A-side supply voltage |
| 42 | 1A4 | Section 1 A-side data input/output 4 |
| 43 | 1A3 | Section 1 A-side data input/output 3 |
| 44 | GND | Ground |
| 45 | 1A2 | Section 1 A-side data input/output 2 |
| 46 | 1A1 | Section 1 A-side data input/output 1 |
| 47 | GND | Ground |
| 48 | 1OE | Active-LOW output enable for section 1 |
Direction Control
The direction-control inputs determine the direction of data transmission between the A and B buses.
| DIR | Data Direction |
|---|---|
| HIGH | A bus to B bus |
| LOW | B bus to A bus |
Output Enable Function
The output-enable inputs are active LOW. When an OE input is LOW, the corresponding transceiver section is enabled. When OE is HIGH, the corresponding outputs enter a high-impedance state.
Each transceiver section has its own DIR and OE signals. This allows section 1 and section 2 to transfer data independently, providing greater flexibility in digital bus architectures.
Design Note: The control inputs are referenced to VCCA. During power-up and power-down, TI recommends using an appropriate pull-up arrangement on the OE inputs to help maintain the high-impedance state. Refer to the official datasheet for the recommended implementation.
6. Specifications
The following table summarizes the key technical specifications of the SN74ALVC164245DGGR.
| Parameter | Specification |
|---|---|
| Manufacturer | Texas Instruments |
| Part Number | SN74ALVC164245DGGR |
| Product Family | ALVC Logic |
| Device Type | Bus Transceiver / Voltage Translator |
| Number of Bits | 16 |
| Transceiver Configuration | Dual 8-Bit |
| Logic Type | Non-Inverting |
| Data Direction | Bidirectional |
| A-Side Supply (VCCA) | 2.5V or 3.3V |
| B-Side Supply (VCCB) | 3.3V or 5V |
| Maximum Data Rate | 300Mbps |
| Maximum Propagation Delay | 5.8ns at 3.3V |
| Output Drive | ±24mA at 3.3V |
| Output Type | 3-State |
| Direction Control | Independent DIR Inputs |
| Output Enable | Active LOW |
| Operating Temperature | -40°C to +85°C |
| Package | TSSOP-48 |
| Package Code | DGG |
| Mounting Type | Surface Mount |
| Package Quantity | 2,000 Pieces per Reel |
| Product Status | ACTIVE |
The maximum data rate and propagation delay are specified under particular operating and test conditions. Actual performance depends on supply voltage, output loading, input transition times, PCB layout, and operating temperature.
7. Equivalent
When selecting an equivalent for the SN74ALVC164245DGGR, engineers should evaluate the number of data channels, voltage translation range, direction-control logic, output-enable behavior, timing performance, output drive capability, and package configuration.
Potential Replacement Components
| Part Number | Manufacturer | Device Function |
|---|---|---|
| SN74LVC16T245 | Texas Instruments | 16-Bit Dual-Supply Bus Transceiver |
| SN74LVCH16T245 | Texas Instruments | 16-Bit Dual-Supply Bus Transceiver |
| 74ALVC164245 | Multiple Manufacturers | 16-Bit Bus Transceiver |
| SN74ALVC164245DGG | Texas Instruments | Same Device, Tube Packaging |
| SN74ALVC164245DGGT | Texas Instruments | Same Device, Smaller Reel Quantity |
Replacement Selection Considerations
- SN74LVC16T245: A newer TI voltage-translating bus transceiver family member worth evaluating for new designs. Verify voltage ranges, timing, control behavior, and package compatibility.
- SN74LVCH16T245: Another potential TI alternative for 16-bit voltage translation. Compare its electrical characteristics and bus-control requirements with the original device.
- 74ALVC164245: A related part designation that may be available from other suppliers. Manufacturer-specific electrical and package details must be checked.
- SN74ALVC164245DGG: Shares the same core device functionality but uses tube packaging rather than the DGGR tape-and-reel ordering option.
Important: The SN74LVC16T245 and SN74LVCH16T245 should be treated as potential redesign alternatives rather than guaranteed pin-to-pin replacements. Before substitution, verify supply ranges, I/O voltage compatibility, direction-control behavior, output-enable polarity, propagation delay, drive strength, and PCB footprint.
8. Manufacturer
Texas Instruments (TI) is a global semiconductor manufacturer specializing in analog integrated circuits, embedded processors, power management, interface products, and standard logic components.
TI's logic portfolio includes a wide range of voltage translators, bus transceivers, buffers, logic gates, multiplexers, and interface devices designed for different digital system requirements.
The SN74ALVC164245 belongs to the ALVC logic family and is part of the Texas Instruments Widebus product portfolio. It is designed to simplify high-speed digital communication between systems operating at different logic voltage levels.
The device's dual-supply structure and independent control channels make it particularly useful in systems where multiple digital buses must communicate reliably across different voltage domains.
Official manufacturer website: Texas Instruments.
Official product page: SN74ALVC164245DGGR Product Information.
9. Applications
The SN74ALVC164245DGGR is suitable for digital electronic systems requiring high-speed parallel data communication and voltage translation between different logic domains.
- Microcontroller Interfaces: Enables communication between microcontrollers and peripherals operating at different logic voltages.
- FPGA Systems: Supports bidirectional parallel data communication between FPGA devices and external digital components.
- Memory Interfaces: Helps connect compatible memory buses and digital control systems operating at different supply voltages.
- Industrial Automation: Provides voltage translation for digital control boards and industrial communication subsystems.
- Printers and Peripherals: Supports parallel data transfer and logic interfacing in electronic peripherals.
- Motor Drives: Provides digital bus interfacing between control processors and compatible electronic subsystems.
- Wireless and Telecom Infrastructure: Supports high-speed digital signal communication across different voltage domains.
- Electronic Point-of-Sale Systems: Helps connect processors, peripheral controllers, and digital interface circuits.
- Embedded Computing: Supports parallel bus communication between processing units and external hardware.
Why Voltage Translation Matters
As electronic systems evolve, different semiconductor generations often use different operating voltages. Older peripheral devices may use 5V logic, while modern processors and programmable logic devices commonly operate at 3.3V or 2.5V.
Directly connecting incompatible logic interfaces can cause unreliable signal interpretation or electrical overstress. A suitable voltage translator provides the required electrical interface between these components.
The SN74ALVC164245DGGR offers a practical solution for these applications through its separate A-side and B-side power rails. Its bidirectional operation allows data to move in either direction without requiring a separate transceiver for each direction.
Design Considerations
When integrating the SN74ALVC164245DGGR into a circuit, designers should first establish the correct VCCA and VCCB supply voltages according to the logic levels of the connected devices.
The DIR signals must be configured to match the required data direction, while the OE signals control whether the corresponding bus outputs are active or placed into a high-impedance state.
For shared bus applications, the output-enable logic must prevent multiple devices from driving the same bus simultaneously. During power-up and power-down, appropriate OE pull-up arrangements should be considered to maintain safe bus isolation.
All unused input pins should be connected to defined logic levels rather than left floating. Proper power supply decoupling, PCB grounding, signal routing, and output loading are also important for achieving reliable high-speed performance.
10. Disclaimer
This product information is provided for general technical reference, engineering evaluation, and electronic component selection purposes. Specifications and electrical characteristics are based on available Texas Instruments documentation and may be updated by the manufacturer.
Customers and design engineers should consult the latest official SN74ALVC164245 datasheet to verify recommended operating conditions, absolute maximum ratings, timing characteristics, input and output specifications, package dimensions, and assembly requirements before using the device in production designs.
Alternative components listed in this article are potential functional alternatives only. Functional similarity does not guarantee pin-to-pin compatibility or electrical interchangeability.
Designers are responsible for validating voltage compatibility, bus timing, output drive, control logic, and power sequencing within the complete electronic system.
Technical Reference
Manufacturer: Texas Instruments
Product: SN74ALVC164245DGGR
Product Family: ALVC / Widebus
Official Product Page: SN74ALVC164245DGGR
Official Datasheet: SN74ALVC164245 Datasheet (PDF)

