Home > The Posts > Product Guides > TPS71530DCKR Texas Instruments | 3.0V 50mA LDO Datasheet, Pinout & Equivalent
TPS71530DCKR - Texas Instruments

TPS71530DCKR Texas Instruments | 3.0V 50mA LDO Datasheet, Pinout & Equivalent

Product Technical Guide TPS71530DCKR 3.0V 50mA Low-Dropout Linear Regulator Technical GuideTexas Instruments fixed-output 3.0V low-dropout linear regulator featuring 50mA output capability, a 2.5V to 2…

In Stock 32,612 Available Inventory
Part No.:
TPS71530DCKR
Manufacturer:
Texas Instruments
Package:
5-TSSOP, SC-70-5, SOT-353
Datasheet:
TPS71530DCKR.pdf
Description:
IC REG LINEAR 3V 50MA SC-70-5
Quantity:
Original Supply

Strict supplier screening and quality control support.

Datasheet Support

Help engineers quickly verify product specifications.

BOM Sourcing

Support multi-part procurement and RFQ matching.

TPS71530DCKR Texas Instruments | 3.0V 50mA LDO Datasheet, Pinout & Equivalent

Product Technical Guide
TPS71530DCKR 3.0V 50mA Low-Dropout Linear Regulator Technical Guide

Texas Instruments fixed-output 3.0V low-dropout linear regulator featuring 50mA output capability, a 2.5V to 24V input voltage range, 3.2µA typical quiescent current, integrated overcurrent protection, and a compact 5-pin SC70 package.

Part NumberTPS71530DCKR
ManufacturerTexas Instruments
Device TypeLow-Dropout Linear Regulator
01

Product Introduction

The TPS71530DCKR is a fixed-output, positive low-dropout (LDO) linear voltage regulator manufactured by Texas Instruments. It belongs to the TPS715 family of micropower voltage regulators designed for battery-powered equipment, low-current control circuits, and compact electronic systems.

The device provides a regulated 3.0V output with an output current capability of up to 50mA. Its low quiescent current helps reduce energy consumption in systems that must remain powered for extended periods.

The TPS715 family supports an input operating voltage range of 2.5V to 24V. However, the fixed 3.0V output can be maintained only when the input voltage is sufficiently higher than the output voltage to satisfy the applicable dropout requirement.

One of the regulator's principal advantages is its very low typical quiescent current of 3.2µA at a 50mA load. Unlike many regulators whose internal supply current increases substantially with load current, the TPS715 is designed to maintain low supply-current consumption across its supported output-current range.

The device also incorporates internal current limiting and soft-start functionality. These features simplify power-supply design and provide additional protection during abnormal load conditions.

The DCKR ordering suffix identifies the 5-pin SC70 surface-mount package supplied in tape-and-reel format.

Typical applications include low-power microcontrollers, battery-powered sensors, industrial monitoring circuits, portable electronic devices, and auxiliary voltage rails.

02

Key Benefits

Ultra-Low Supply Current

3.2µA typical quiescent current supports low-power and long-duration battery-operated designs.

Wide Input Voltage Range

Accepts input voltages from 2.5V to 24V, subject to output regulation and thermal limits.

Compact SC70 Package

Five-terminal surface-mount package minimizes PCB space requirements.

Integrated Protection

Built-in overcurrent protection and soft-start reduce external circuit complexity.

03

Features

  • Fixed 3.0V positive output voltage
  • Maximum rated output current of 50mA
  • 2.5V to 24V input voltage operating range
  • 3.2µA typical quiescent current at a 50mA load
  • Low-dropout linear regulator architecture
  • Approximately 415mV typical dropout voltage at 50mA for the newer silicon implementation
  • Integrated overcurrent protection
  • Internal soft-start functionality
  • Stable with suitable output capacitance of at least 0.47µF effective
  • Recommended 1µF or larger nominal output capacitor
  • Recommended input bypass capacitor of 0.1µF or larger
  • Low power consumption for battery-powered circuits
  • No external feedback divider required for the fixed-output version
  • Five-pin SC70 surface-mount package
  • Operating junction temperature range of -40°C to +125°C
  • Tape-and-reel ordering configuration

Important: TPS71530DCKR is a 50mA regulator, not a 250mA regulator. Designs requiring higher output current should use a regulator with an appropriately rated output-current capability.

04

Package

The TPS71530DCKR is available in Texas Instruments' DCK package, a five-pin SC70 surface-mount package.

  • Package Code: DCK
  • Package Type: SC70-5
  • Alternative Package Designation: SOT-353
  • Number of Pins: 5
  • Mounting Type: Surface Mount
  • Approximate Package Body: 2.0mm × 1.25mm
  • Operating Junction Temperature: -40°C to +125°C
  • Packaging: Tape and Reel
  • Ordering Part Number: TPS71530DCKR

The miniature SC70 package makes the device suitable for high-density PCB assemblies and portable electronic products.

Because of the small package size, thermal performance depends strongly on PCB layout, copper area, ambient temperature, and the difference between input and output voltage.

For mechanical design and assembly, use the official Texas Instruments DCK package drawing rather than dimensions taken from a generic SOT-23 illustration.

05

Pinout

The fixed-output TPS71530DCKR uses five pins, including two no-connect terminals.

Pin Number Pin Name Description
1 NC No internal connection.
2 GND Ground reference for the regulator.
3 NC No internal connection.
4 IN Input supply voltage connection.
5 OUT Regulated 3.0V output.
Pin 1 – NCNo internal connection; follow TI layout guidance.
Pin 2 – GNDConnect to the circuit ground plane.
Pin 3 – NCNo internal connection; follow TI layout guidance.
Pin 4 – INConnect to the input power source with appropriate bypass capacitance.
Pin 5 – OUTProvides the regulated 3.0V output to the load.

Input Capacitor: Connect a 0.1µF or larger capacitor between IN and GND, placed close to the regulator.

Output Capacitor: Connect a nominal 1µF or larger capacitor between OUT and GND. Ensure that the effective capacitance after voltage, temperature, and tolerance derating remains above the required minimum.

Pinout Warning: The adjustable TPS715 variant uses a feedback input on pin 1, while the fixed 3.0V TPS71530DCKR uses pin 1 as NC. Do not substitute the adjustable-version schematic without reviewing the corresponding pin functions.

06

Specifications

Parameter Value
Part Number TPS71530DCKR
Manufacturer Texas Instruments
Product Family TPS715
Device Type Low-Dropout Linear Regulator
Output Configuration Positive
Output Type Fixed
Number of Outputs 1
Nominal Output Voltage 3.0V
Maximum Output Current 50mA
Minimum Input Operating Voltage 2.5V
Maximum Input Operating Voltage 24V
Typical Quiescent Current 3.2µA at 50mA output load
Typical Dropout Voltage 415mV at 50mA for newer silicon
Output Capacitor Requirement At least 0.47µF effective capacitance
Recommended Nominal Output Capacitor 1µF or larger
Recommended Input Capacitor 0.1µF or larger
Overcurrent Protection Integrated
Soft-Start Integrated
Operating Junction Temperature -40°C to +125°C
Package SC70-5 / DCK
Pin Count 5
Mounting Type Surface Mount
Packaging Tape and Reel

Input Voltage: The regulator can accept input voltages across the specified operating range, but the input must remain sufficiently above 3.0V to maintain regulation. For example, a 2.5V input cannot produce a regulated 3.0V output from this linear regulator.

Dropout Voltage: Dropout is the minimum input-to-output voltage difference required for the regulator to maintain the specified output under given operating conditions. The TPS715 datasheet distinguishes between legacy and newer silicon characteristics, so designers should use the applicable revision and worst-case limits.

Quiescent Current: Low internal supply current is especially valuable in always-on sensor nodes and low-duty-cycle embedded equipment.

Power Dissipation: Approximate regulator dissipation can be estimated using P = (VIN - VOUT) × IOUT, with a small additional contribution from quiescent current.

Example: At VIN = 12V, VOUT = 3.0V, and IOUT = 20mA, the approximate pass-element dissipation is (12V - 3V) × 0.02A = 0.18W. The resulting junction temperature must be checked against the SC70 package thermal characteristics.

Output Capacitor: Ceramic capacitors may lose significant effective capacitance under DC bias. Select a capacitor whose effective value satisfies the datasheet requirement under actual operating conditions.

Current Limit: Internal overcurrent protection helps protect the device from excessive load current, but it does not make the regulator suitable for continuous operation above its 50mA rating.

07

Equivalent

When selecting a TPS71530DCKR equivalent or replacement, engineers should compare fixed output voltage, maximum load current, input voltage range, quiescent current, dropout voltage, stability requirements, package footprint, and pin configuration.

TPS71530DCKRM3: A related Texas Instruments 3.0V TPS715 ordering variant. Confirm the manufacturer's current ordering information, silicon revision, and package compatibility before substitution.

TPS71530QDCKRQ1: An automotive-qualified member of the TPS715 family with a fixed 3.0V output. Its qualification and electrical characteristics must be checked against the original design requirements.

TPS71533DCKR: A related TPS715 family device with a fixed 3.3V output. It is not a direct voltage-equivalent replacement for a 3.0V rail.

TPS715A Family: Texas Instruments offers related devices for applications requiring different current or package capabilities. Verify the exact device configuration before redesign.

Other 3.0V LDO Regulators: Alternative manufacturers provide fixed-output LDO regulators with different current ratings and standby-current characteristics. Matching output voltage alone does not establish electrical or mechanical compatibility.

Replacement Recommendation: For existing designs, prioritize the same TPS71530 device configuration and confirm the SC70-5 pinout. Alternatives must be evaluated for input-voltage tolerance, startup behavior, dropout, stability, thermal dissipation, and supply-current consumption.

08

Manufacturer

Texas Instruments Incorporated is a global semiconductor manufacturer specializing in analog integrated circuits, embedded processing, power management, and signal-chain technologies.

The TPS715 series is part of TI's low-power linear-regulator portfolio, designed to support compact power-management systems and battery-operated applications.

Official Product Page: Texas Instruments TPS715

Official Datasheet: TPS715 50mA Low-Dropout Linear Regulator Datasheet

Manufacturer Website: www.ti.com

Distributor Reference: TPS71530DCKR Product Listing

For purchasing, confirm the complete ordering part number, manufacturer labeling, production traceability, reel packaging, and current lifecycle information.

09

Applications

Battery-Powered Electronics

Low-current regulated supply rails for portable electronic equipment.

Microcontroller Power Supply

Provides a regulated 3.0V rail for compatible low-power MCUs.

Sensor Power Management

Supplies low-current sensors and measurement interfaces.

Monitoring Systems

Supports low-duty-cycle electronic monitoring and data-acquisition circuits.

Industrial Control Modules

Generates a low-current auxiliary 3.0V supply within suitable thermal limits.

Portable Devices

Supports compact electronics requiring low standby consumption.

Typical Application Circuit: Connect the input supply to pin 4 (IN), the system ground to pin 2 (GND), and the regulated load to pin 5 (OUT).

Place a 0.1µF or larger input capacitor close to IN and GND. Connect a suitable 1µF or larger nominal output capacitor between OUT and GND, ensuring the effective capacitance remains above the specified minimum.

Battery-Powered Design: Low quiescent current can help extend battery life in devices that remain energized while the main processor or sensor spends much of its time in a low-power state.

Microcontroller Applications: A regulated 3.0V output can power compatible low-current MCU devices. Verify the processor's peak current during startup, radio transmission, and peripheral operation.

Sensor Applications: The regulator can provide a stable supply for sensors with current requirements within the 50mA rating. Noise-sensitive circuits should be evaluated using the manufacturer's electrical performance data.

Thermal Considerations: Large input-to-output voltage differences increase power dissipation in a linear regulator. A 24V input supplying a 3.0V load requires particular attention to current and thermal constraints.

PCB Layout: Keep the input and output bypass capacitors close to the regulator. Use short ground connections and avoid routing high-current switching traces near sensitive analog supply paths.

System Validation: Verify input transients, output accuracy, startup behavior, capacitor stability, load regulation, and junction temperature under expected operating conditions.

10

Disclaimer

This technical guide is provided for product identification, engineering reference, and procurement support. All specifications, electrical characteristics, package dimensions, pin assignments, capacitor requirements, thermal ratings, and protection functions should be verified against the latest official Texas Instruments datasheet before design or purchase. The TPS71530DCKR is rated for a maximum output current of 50mA and must not be treated as a 250mA regulator. Dropout characteristics and selected electrical parameters may differ between silicon revisions. Suggested alternatives are not guaranteed pin-compatible or functionally equivalent. Product availability, lifecycle status, pricing, and lead times may change without notice.

Quick RFQ Send your inquiry and our sales team will respond quickly.

Part Number
Quantity*
Price
Name*
Company*
Email*
Comments
```