Home > The Posts > Product Guides > UA9638CDR Texas Instruments | Dual High-Speed Differential Line Driver Technical Guide
UA9638CDR - Texas Instruments

UA9638CDR Texas Instruments | Dual High-Speed Differential Line Driver Technical Guide

Product Technical Guide UA9638CDR Dual High-Speed Differential Line Driver Technical GuideTexas Instruments dual high-speed differential line driver designed for EIA/TIA-422-B communication, featuring …

In Stock 0 Available Inventory
Part No.:
UA9638CDR
Manufacturer:
Texas Instruments
Package:
8-SOIC (0.154", 3.90mm Width)
Datasheet:
UA9638CDR.pdf
Description:
IC DRVR 8-SOIC
Quantity:
Original Supply

Strict supplier screening and quality control support.

Datasheet Support

Help engineers quickly verify product specifications.

BOM Sourcing

Support multi-part procurement and RFQ matching.

UA9638CDR Texas Instruments | Dual High-Speed Differential Line Driver Technical Guide

Product Technical Guide
UA9638CDR Dual High-Speed Differential Line Driver Technical Guide

Texas Instruments dual high-speed differential line driver designed for EIA/TIA-422-B communication, featuring two independent drivers, a single 5V supply, up to 15Mbps signaling, TTL/CMOS-compatible inputs, output short-circuit protection, and an 8-pin SOIC package.

Part NumberUA9638CDR
ManufacturerTexas Instruments
Device TypeDual Differential Line Driver
01

Product Introduction

The UA9638CDR is a dual high-speed differential line driver manufactured by Texas Instruments. Designed to meet or exceed ANSI EIA/TIA-422-B requirements, it converts two single-ended digital input signals into two pairs of complementary differential output signals.

The device is intended for high-speed digital communication across twisted-pair transmission lines. Differential signaling helps improve noise immunity and signal integrity in electrically noisy environments, including factory automation equipment and industrial control systems.

The UA9638CDR operates from a single nominal 5V power supply and supports signaling rates up to 15Mbps. It can drive differential loads as low as 50Ω under specified operating conditions.

Its input stages are compatible with TTL and CMOS logic levels, allowing connection to microcontrollers, programmable logic devices, and digital communication controllers with suitable voltage levels.

Schottky-diode-clamped transistor circuitry minimizes propagation delay, while integrated output short-circuit protection improves robustness under fault conditions.

The device provides two transmitters and no receivers. For a complete receive path, a separate differential line receiver such as the Texas Instruments UA9637A may be used.

The UA9638CDR is supplied in an 8-pin SOIC package with tape-and-reel packaging. It is specified for operation from 0°C to +70°C and is suitable for commercial-temperature communication and control equipment.

02

Key Benefits

Dual Differential Outputs

Two independent drivers convert single-ended logic signals into complementary differential output pairs for reliable communication.

High-Speed Transmission

Supports signaling rates up to 15Mbps for industrial data links and high-speed digital interfaces.

Single 5V Supply

Operates from a nominal 5V supply without requiring separate positive and negative power rails.

Short-Circuit Protection

Integrated output protection helps limit damage from certain output fault conditions.

03

Features

  • Dual high-speed differential line driver
  • Two independent transmitter channels
  • Meets or exceeds ANSI EIA/TIA-422-B requirements
  • Single nominal 5V power supply
  • Recommended supply voltage range of 4.75V to 5.25V
  • Maximum specified signaling rate of 15Mbps
  • Supports differential loads as low as 50Ω
  • TTL-compatible digital inputs
  • CMOS-compatible input interface
  • Complementary differential output pairs
  • Schottky-clamped transistor design for reduced propagation delay
  • Input clamp diodes
  • Integrated output short-circuit protection
  • Suitable for twisted-pair cable transmission
  • Compatible with differential receivers such as UA9637A
  • Functionally interchangeable with the DS9638 family, subject to verification
  • Commercial operating temperature range of 0°C to +70°C
  • 8-pin SOIC surface-mount package
  • Tape-and-reel packaging
  • RoHS-compliant ordering option

Design Note: The UA9638CDR is a differential line driver rather than a complete RS-422 transceiver. It does not contain receiver channels or an integrated galvanic isolation barrier.

04

Package

The UA9638CDR uses the Texas Instruments D package, an 8-pin small-outline integrated circuit (SOIC) suitable for automated surface-mount PCB assembly.

  • Package Type: SOIC
  • Package Code: D
  • Pin Count: 8
  • Mounting Type: Surface Mount
  • Nominal Package Size Including Leads: 4.9mm × 6.0mm
  • Nominal Body Width: 3.9mm
  • Nominal Lead Pitch: 1.27mm
  • Packaging: Tape and Reel
  • Standard Reel Quantity: 2,500 pieces
  • Moisture Sensitivity Level: MSL 2
  • Peak Reflow Temperature: 260°C
  • Lead Finish: NiPdAu
  • RoHS Compliance: Yes
  • REACH Compliance: Yes

The SOIC-8 package offers a compact footprint for designs requiring two differential transmission channels without additional receiver circuitry.

PCB designers should place the power supply decoupling capacitor close to the VCC and GND pins. Differential traces should be routed as closely coupled pairs with appropriate impedance control and termination for the selected cable and transmission environment.

05

Pinout

The UA9638CDR pinout contains two single-ended logic inputs, four differential output pins, one positive supply pin, and one ground pin.

Pin Signal Function
1 VCC Positive 5V power supply input.
2 1A Single-ended digital input for differential driver channel 1.
3 2A Single-ended digital input for differential driver channel 2.
4 GND Ground reference.
5 2Z Complementary inverted output of driver channel 2.
6 2Y Non-inverted output of driver channel 2.
7 1Z Complementary inverted output of driver channel 1.
8 1Y Non-inverted output of driver channel 1.
Pin 1 – VCCConnect to a regulated 5V supply within the recommended operating range.
Pin 2 – 1ADigital input controlling differential output pair 1Y and 1Z.
Pin 3 – 2ADigital input controlling differential output pair 2Y and 2Z.
Pin 4 – GNDCommon ground reference for the device.
Pins 5 and 6 – 2Z / 2YComplementary differential outputs for the second driver channel.
Pins 7 and 8 – 1Z / 1YComplementary differential outputs for the first driver channel.

Logic Operation: When input 1A is high, output 1Y is driven high and 1Z is driven low. When 1A is low, the corresponding output polarities reverse. Driver channel 2 operates in the same manner using 2A, 2Y, and 2Z.

Important: The pin assignments above apply to the 8-pin D-package device. Verify pin numbering, signal polarity, and PCB footprint against the latest Texas Instruments datasheet before finalizing the design.

06

Specifications

Parameter Value
Part Number UA9638CDR
Manufacturer Texas Instruments
Device Type Dual High-Speed Differential Line Driver
Interface Standard ANSI EIA/TIA-422-B
Number of Transmitters 2
Number of Receivers 0
Maximum Signaling Rate 15Mbps
Nominal Supply Voltage 5V
Recommended Supply Voltage 4.75V to 5.25V
Minimum Input High Voltage 2.0V
Maximum Input Low Voltage 0.8V
Logic Input Compatibility TTL and CMOS
Minimum Supported Differential Load 50Ω under specified conditions
Output Short-Circuit Protection Yes
Maximum Supply Current 65mA, according to TI product summary
Operating Temperature Range 0°C to +70°C
Package Type SOIC
Package Code D
Pin Count 8
Mounting Type Surface Mount
Packaging Tape and Reel
Standard Package Quantity 2,500
Moisture Sensitivity Level MSL 2
RoHS Compliance Yes
REACH Compliance Yes
Product Status ACTIVE

Supply Requirements: The device is designed for a regulated 5V supply. Operating outside the recommended 4.75V to 5.25V range may affect output performance and reliability.

Data Transmission: The maximum specified signaling rate is 15Mbps. Achievable cable length and signal integrity depend on cable characteristics, termination, common-mode noise, and system layout.

Differential Output: Each driver produces complementary output signals suitable for differential transmission. The receiver interprets the voltage difference between the Y and Z lines rather than relying on a single-ended signal reference.

Temperature Limitation: The UA9638CDR is specified for commercial-temperature operation from 0°C to +70°C. It should not be treated as an industrial-temperature or automotive-qualified component without additional qualification.

Protection: Output short-circuit protection is provided, but this feature does not replace system-level surge, electrostatic discharge, or transient protection where required.

07

Equivalent

When evaluating a UA9638CDR equivalent or replacement, engineers should compare driver count, differential output characteristics, supply voltage, data rate, logic input thresholds, temperature range, package, and pin compatibility.

UA9638CDR: The original Texas Instruments ordering number is the preferred option for existing PCB designs. The R suffix identifies tape-and-reel packaging.

UA9638CD: An older ordering variant of the same device in SOIC-8 packaging. Texas Instruments identifies UA9638CDR as its replacement; the UA9638CD ordering variant is obsolete.

UA9638CDRG4: An alternative ordering designation identified by Texas Instruments as equivalent to UA9638CDR. Verify current ordering and packaging arrangements with the manufacturer or authorized distributor.

DS9638: A historically interchangeable dual differential line-driver family identified in the Texas Instruments datasheet. Availability, manufacturing source, and electrical specifications must be checked before substitution.

SN75ALS191: A Texas Instruments differential line driver recommended in the UA9638 documentation for faster switching in the same pin configuration. Electrical characteristics and system compatibility must still be verified.

Modern RS-422 Drivers: Other dual-channel differential drivers may provide similar communication functionality. However, devices with enable pins, different output protection, different supply requirements, or alternative pin assignments are not necessarily direct replacements.

Replacement Recommendation: For an existing UA9638CDR PCB, prioritize the exact ordering number. For new designs, compare the SN75ALS191 and newer RS-422 driver options according to speed, temperature range, protection requirements, lifecycle, and package compatibility.

08

Manufacturer

Texas Instruments Incorporated is a global semiconductor manufacturer specializing in analog integrated circuits, embedded processing, power management, and interface technologies.

The UA9638 belongs to the company's differential interface product portfolio and is designed for applications requiring high-speed data transmission over balanced signal lines.

The UA9638CDR remains an active ordering option in the manufacturer's product catalog.

Official Product Page: UA9638 – Texas Instruments

Official Ordering Information: UA9638CDR Part Details

Official Datasheet: UA9638 Dual High-Speed Differential Line Driver Datasheet

Manufacturer Website: www.ti.com

For purchasing and quality control, verify the original manufacturer, complete ordering number, packaging type, traceability information, and relevant compliance documentation.

09

Applications

Factory Automation

Differential communication between controllers, industrial equipment, and automation modules operating in electrically noisy environments.

AC and Servo Motor Drives

High-speed differential transmission of digital control and status signals between motor-control circuits and related equipment.

Smart Grid Equipment

Balanced digital signaling for communication interfaces within compatible energy monitoring and control systems.

ATM and Cash Counters

Reliable differential communication for electronic transaction equipment, counting machines, and associated control electronics.

Industrial Data Links

Transmission of high-speed digital data through twisted-pair cables using appropriate differential receivers and termination.

Embedded Communication Systems

Conversion of TTL/CMOS digital signals into balanced differential signals for controller-to-controller communication.

Typical Application: A microcontroller or programmable logic device drives the 1A and 2A inputs of the UA9638CDR. Each input is converted into a complementary differential output pair, 1Y/1Z or 2Y/2Z, for transmission through a suitable twisted-pair cable.

At the receiving end, a compatible differential receiver such as the UA9637A converts the differential signal back into a single-ended digital signal for processing by the receiving controller.

Termination: Select termination resistance according to the characteristic impedance of the transmission line and the system topology. Termination values and placement should be verified for the intended cable length and signaling rate.

PCB Layout: Keep differential traces closely coupled, minimize stubs, use appropriate decoupling, and avoid routing high-speed signal pairs near switching power components when possible.

Protection Consideration: External TVS diodes, common-mode filtering, or galvanic isolation may be required for exposed connectors, harsh industrial environments, or installations with significant ground potential differences.

10

Disclaimer

This technical guide is provided for general product identification, engineering reference, and procurement support. All specifications, pin assignments, data rates, operating conditions, electrical limits, package dimensions, protection characteristics, environmental compliance information, and product lifecycle status should be verified against the latest Texas Instruments documentation before design or purchase. Suggested alternatives are not guaranteed direct replacements. Actual communication performance depends on cable characteristics, termination, system topology, PCB layout, operating conditions, and external protection circuitry. Product prices and availability may change without notice.

Quick RFQ Send your inquiry and our sales team will respond quickly.

Part Number
Quantity*
Price
Name*
Company*
Email*
Comments
```